Ota yhteyttä
020 789 5900 tai Lomakkeella
Tarjouspyyntö 0
Fescotop F10 Floor hardener
Fescotop F45K Floor hardener
Fescotop F300 Floor hardener
Fescotop F90K High-performance concrete
Curing compound
« Takaisin tuoteryhmään

Fescotop F10 Floor hardener

Kysy lisätietoa

Tuotekuvaus

Fescotop F10 is a quartz aggregate, cement-based dry-shake floor hardener made in Finland for application on fresh concrete surfaces. Wear resistance class A9. Suitable for use in areas of moderate wear and tear.

Fescotop floor hardener forms a tread on the surface of the concrete floor to improve durability and tightness. The floor surface will be dust-free and very easy to maintain. Suitable for indoor and outdoor use.

  • Wear resistance class A9
  • Material usage 3 - 8 kg/m2
  • Maximum grain size 3 mm
  • Increases the wear and shock resistance of the floor
  • Improves the chemical resistance of the floor against oils and greases

Stock products: concrete grey (natural) and bright grey. On request: dark grey, black grey. Special colours can be tinted for each project. Minimum production run 3 pallets. 

Käyttökohteet

  • Lightly-loaded public spaces
  • Garages and carports
  • Lightly-loaded industrial halls and warehouses
  • Parking garages in apartment buildings
Tuote on listattu Pohjoismaisen Ympäristömerkinnän rakennustuotetietokantaan ja sitä voidaan käyttää Joutsenmerkityissä rakennuksissa.
GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841770035 FESCOTOP F10 3 MM BETONINHARMAA (NATURAL) 25 KG 77003 25 kg
6416841771209 FESCOTOP F10 3 MM KIRKASHARMAA 25 KG 77120 25 kg
6416841770592 FESCOTOP F10 3 MM TUMMANHARMAA 25 KG 77059 25 kg
6416841770608 FESCOTOP F10 3 MM MUSTANHARMAA 25 KG 77060 25 kg

Base

  • Betongens rekommenderade hållfasthet är C25/30, vattencementtalet minst 0,5.
  • Betong med högre hållfasthetsklass har lägre vattencementtal. Då räcker vattenmängden nödvändigtvis inte till för att fukta den utspridna golvhärdaren tillräckligt vilket kan orsaka en risk att produkten fäster på underlagsbetongen.
  • Betongens luftmängd är max 3 %. Med golvbetong med kraftiga porer kan det uppstå ett fästproblem mellan härdarens yta och underlagsmassan.
  • Temperaturen i underlaget bör vara minst +10°C.

Application

  • The workspace must be protected from strong wind, sunlight and rain.
  • Before applying the hardener, the concrete should be rubbed open to ensure that the concrete surface has sufficient moisture for the dry-shake to adhere.
  • After rubbing, apply the dry-shake either manually or mechanically to the concrete surface in as even a layer as possible. If the application is carried out mechanically, the entire quantity is applied in one go.
  • If the amount to be applied by hand is about 6 kg/m2 or more, two applications are recommended.
  • Before rubbing, the dry-shake should be thoroughly moistened with water.
  • The rubbing of the dry-shake is first done with a low-speed machine. The continue rubbing until the dry-shake forms a plastic layer on top of the concrete.
  • The finishing of the hardened floor, i.e. the shining, is started with a low-speed rubbing machine, with the levelling wings flat. Final finishing, shining, is done later on with the same machine, but at a higher speed.
  • Wash the tools immediately with water after the work is completed.

Curing

  • The dry-shake floor is refinished immediately after the last round of shining with Fesco's curing compound.
  • Curing can be continued with water spraying or by placing a plastic film, a filter cloth on the floor, or with a combination of both.
  • The duration of the curing is estimated by the flooring contractor together with the customer. The duration is affected by the type of concrete used, the conditions and the requirements of the site. As a general rule, curing should be continued for at least 7 to 14 days.

Other considerations

  • If the air content of the concrete is high and the effective water-binder ratio is low, the adhesion of the dry-shake coating may be poor. When using a dry-shake coating in a frost-resistant structure, the amount of air in the concrete can be limited to a maximum of 3%. The frost resistance of the concrete used must be demonstrated with preliminary tests. (reference: By 68 Concrete selection and service life design – A guide for designers 2024, page 79).

Covering

  • The product does not need to be coated.
  • Can be polished and used as a so-called design surface.

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Materiaalimenekki

3 - 8 kg/m2, depending on the requirements set for the base, concrete quality, and working conditions
Light to average load 3 - 5 kg/m2
Average to heavy load 5 - 8 kg/m2
Coloured floors, light colours in particular 5 - 8 kg/m2
Olomuoto Powder
Sideaine Special cement
Väri Concrete grey, bright grey, dark grey, black grey
Maksimiraekoko

3 mm
Pakkauskoko 25 kg
Varastointi

Storage time in a dry location approx. 12 months
Käyttölämpötila

At least +10°C
Kuivumisaika

Pedestrian traffic 1 - 2 days
Light traffic 7 - 10 days
Fully dried 28 days
Lujuusluokka C 60 (EN 13818)
Taivutusvetolujuus F 6 (EN 13813)
Kulutuskestävyys

A9 (Böhme-test 7,8 cm3 / 50 cm2
Palokäyttäytyminen A1
Pakkasenkestävyys Frostproof
Vedenkestävyys

Waterproof
Vastuunrajaus, tuotteen käyttöön liittyvät huomiot ja rajoitukset: Tutustu Fescon Oy:n yleisiin toimitusehtoihin ja tuotteeseen liittyviin suunnittelu- sekä työohjeisiin.