Ota yhteyttä
020 789 5900 tai Lomakkeella
Tarjouspyyntö 0
Masonry mortar M100/600
Masonry mortar M100/600 Winter
Compact mortar M100/600
Compact mortar M100/600 Winter
Compact mortar Heavy M100/600
Compact mortar Heavy M100/600 Winter
Winter-time masonry mortar TML
Block mortar M100/500
Block mortar M100/500 Winter
Stone adhesive KVL
Mortar for tongue-and-groove blocks PHL
Mortar for tongue and groove blocks PHL Winter
ELT Brick element grout
ELK Clinker element grout
« Takaisin tuoteryhmään

Compact mortar M100/600

Kysy lisätietoa

Tuotekuvaus

Fescon Compact mortar M100/600 is a cement-based mortar for burnt and sand-lime brick masonry for facades exposed to harsh weather conditions. Suitable for locations subject to heavy slanted rain. Suitable for repointing brickwork and natural and slate stones on vertical surfaces, and for repairing mortar joints. Contains additives to improve density, weather resistance and workability. 

  • For the masonry of facades exposed to harsh weather conditions
  • Low water absorption value
  • Reduces the water permeability of the cavity wall
  • Compressive strength M 5
  • Available in 20 standard colours. Colored products are custom-made products, see delivery terms and conditions
  • Special colours can be tinted to match the project requirements

Käyttökohteet

  • For work jointing and jointing of natural and slate stones on vertical surfaces
  • For repairing existing mortar joints
  • For repointing of brickwork
  • Facade masonry in locations subjected to heavy slanted rain
Tuote on listattu Pohjoismaisen Ympäristömerkinnän rakennustuotetietokantaan ja sitä voidaan käyttää Joutsenmerkityissä rakennuksissa.
GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841331007 TIIVISLAASTI M100/600 1000 KG 33100 1000 kg
6416841331335 TIIVISLAASTI 39 KVARTSINVALKOINEN 1000 KG 33133 1000 kg
6416841331014 TIIVISLAASTI 59 TUOHENVALKOINEN 1000 KG 33101 1000 kg
6416841331045 TIIVISLAASTI 40 KALKINHARMAA 1000 KG 33104 1000 kg
6416841331038 TIIVISLAASTI 41 VILJANKELTAINEN 1000 KG 33103 1000 kg
6416841344250 TIIVISLAASTI 42 TIILENPUNAINEN 1000 KG 34425 1000 kg
6416841331052 TIIVISLAASTI 45 MULLANRUSKEA 1000 KG 33105 1000 kg
6416841331069 TIIVISLAASTI 46 TURPEENRUSKEA 1000 KG 33106 1000 kg
6416841331076 TIIVISLAASTI 48 MUSTANHARMAA 1000 KG 33107 1000 kg
6416841344274 TIIVISLAASTI 52 PELLAVANVAALEA 1000 KG 34427 1000 kg
6416841344182 TIIVISLAASTI 44 HIEKANRUSKEA 1000 KG 34418 1000 kg
6416841344137 TIIVISLAASTI 71 JOUTSEN 1000 KG 34413 1000 kg
6416841344168 TIIVISLAASTI 72 ALLI 1000 KG 34416 1000 kg
6416841344083 TIIVISLAASTI 73 KÄKI 1000 KG 34408 1000 kg
6416841344144 TIIVISLAASTI 74 HAUKKA 1000 KG 34414 1000 kg
6416841344113 TIIVISLAASTI 75 KIURU 1000 KG 34411 1000 kg
6416841344120 TIIVISLAASTI 77 NAAKKA 1000 KG 34412 1000 kg
6416841344106 TIIVISLAASTI 79 KIIRUNA 1000 KG 34410 1000 kg
6416841344243 TIIVISLAASTI 80 KUUKKELI 1000 KG 34424 1000 kg
6416841344298 TIIVISLAASTI 81 TAVI 1000 KG 34429 1000 kg
6416841344151 TIIVISLAASTI 82 METSO 1000 KG 34415 1000 kg
6416841344229 TIIVISLAASTI 83 RIEKKO 1000 KG 34422 1000 kg
6416841344199 TIIVISLAASTI 85 KORPPI 1000 KG 34419 1000 kg
6416841344236 TIIVISLAASTI 86 PYY 1000 KG 34423 1000 kg

Base

  • The temperature of the masonry brick or structure is above > 0°C
  • Brick, natural stone, slate
  • Brick pallets are protected from rain. The bricks must not be wet or covered with snow or ice.

Priming

  • Masonry structures are not primed

Mixing and application of the product

  • Masonry work should not be carried out in direct sunlight, in the rain or during strong winds.
  • The working temperature should be between +5°C and +25°C.
  • A bag (25 kg) of dry powder is mixed with 2.9 to 3.8 litres of clean water. 
  • Do not add all the water at first. The mixture contains the correct amount of water when the mortar holds its shape and no water rises to the surface.
  • The amount of water must be as instructed in the product card. Deviating from the recommended amount of water lowers the mortar’s strength properties, increases the risk of separation, affects the strength development and reduces workability. 
  • Product is mixed with a mortar stirrer, in a concrete mixer, or with a pan-mixer or a continuous mixer to a smooth consistency. The maximum mixing time is approx. 10 minutes.
  • If the working conditions are very dry or warm, it is possible to improve the adhesion by dampening the masonry joints or bricks. There should not be water drops on the substrate.  
  • Keep the amount of water the same during jointing, because any variations in the amount of water will show as colour differences in the joint.
  • The jointing technique affects the density of the mortar joint. Finish the jointing by sealing them with a brick jointer and removing any excess mortar from the brickwork by brushing diagonally over the joints with a masonry brush.
  • The expansion joints are provided as defined in the structural plans.
  • The working time of the compact mortar is about 3 hours. 
  • When finished working, wash the tools immediately with water.
  • Remove any dried mortar mechanically.
  • After casting you should keep the mortar joints moist by fog spraying for about 3 days depending on the conditions or the target.

Repointing to a previously masonry joint

  • Available in 20 standard colours. Special colours are subject to order.
  • When repointing, the old mortar must first be removed to a depth of at least 20 mm, but no more than 15% of the masonry depth or according to the designer’s instructions. 
  • The joint is cleaned of dust and dampened.
  • When repointing, add the dry powder to the instructed amount of water and let it stand for about 10 minutes. After that, remix the paste and add masonry mortar to make the paste semi-dry. This mixing method ensures the sufficient air content of the mortar.
  • When repointing, start first with vertical joints and after that work with the horizontal ones. Repoints that are over 20 mm are done in two phases.
  • The working time of a semi-dry mortar for repointing is 1 to 2 hours.
  • After casting you should keep the mortar joints moist by fog spraying for about 3 days depending on the conditions or the target.
  • Bases or masonry units with low water absorption are repointed with Repairing plaster KL 1.2 or Facade coating JSP 1.5.

Other points to note

  • Construction planner instructions and official regulations are to be followed in all masonry work.
  • Not suitable for masonry of the inner shells of fireplaces or wood-burning stoves nor masonry of chimney flues indoors.
  • Masonry mortars may have slight differences in shade between small and big bags, as well as between the mortars intended for winter and summer time masonry, so it is not advisable to change the type of mortar in the middle of the wall.
  • Meets the requirements of Annex 4 of the national standard SFS 7001.

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Vedentarve 2.9 - 3.8 l/25 kg
Olomuoto powder
Sideaine cement
Väri available in 20 standard colours, special colours subject to order
Maksimiraekoko

2.0 mm
Pakkauskoko 1000 kg
Varastointi

storage time in a dry location approx. 1 year
Lisäaineet

additives that improve density, weather resistance and workability
Käyttölämpötila

+5°C...+25°C
Työstettävyysaika 3 h
Puristuslujuus

M 5
Tartuntalujuus

≥0.16 N/mm2 (SFS-EN 998-2, 5.4.2 a)
Palokäyttäytyminen A1
Lämmönjohtavuus 0.82 [w/(m•K)], P=50%
Kloridipitoisuus < 0.1 % (EN 998-2:2016)
Pakkasenkestävyys yes
Vedenimukerroin

0.05 kg/(m2 · min0,5) (EN1015-18)
Vastuunrajaus, tuotteen käyttöön liittyvät huomiot ja rajoitukset: Tutustu Fescon Oy:n yleisiin toimitusehtoihin ja tuotteeseen liittyviin suunnittelu- sekä työohjeisiin.