Ota yhteyttä
020 789 5900 tai Lomakkeella
Tarjouspyyntö 0
Waterproofing compound
Waterproofing compound WS
Fescoseal A+B
Adhesion promoter
Primer KP
Waterproofing strip
Drain flange 300x300 mm fibre
Drain flange KL-B
Waterproofing accessories FS
Waterproofing accessories VE
Tile adhesive plaster VSL
Tile adhesive plaster ILL
Tile adhesive plaster SS2
Tile adhesive plaster SSL Lite
Tile seaming plaster SML
Sanitary silicone
« Takaisin tuoteryhmään

Tile adhesive plaster SS2

Kysy lisätietoa

Tuotekuvaus

Fescon Tile Adhesive Plaster SS2 is an M1-rated dry mortar with a cement binder. Enables tiling of structures that require particular flexibility from the plaster, see research report VTT-S-03707-10. 

  • Easy to use
  • Good workability characteristics
  • Good adhesion strength (>2 N/mm2 )
  • Meets the C2 tensile strength requirements
  • S2-flexibility classification (> 5 mm)
  • For floors with underfloor heating

Käyttökohteet

  • Suitable for the tiling of sheet metal bathrooms, structures with wooden frames, and other structures requiring flexibility, and both indoor and outdoor surfaces subject to temperature variations, and also for floors with underfloor heating.
Tuote on listattu Pohjoismaisen Ympäristömerkinnän rakennustuotetietokantaan ja sitä voidaan käyttää Joutsenmerkityissä rakennuksissa.
GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841203038 SANEERAUSLAASTI SS2 20 KG 20303 20 kg

Base

  • Clean, undamaged, dust-free and level
  • If you are laying tiles on top of an old coating, you must ensure the adhesion of the old coating and roughen the base.
  • Sufficient strength and load-bearing capacity
  • Switch underfloor heating off two days before tiling
  • The relative humidity of the underfloor structure is less than 90% RH
  • Temperature > + 10°C
  • Loose coatings, cement paste and other impurities must be mechanically removed
  • Maximum humidity 95% RH

Instructions for use

  • Mix a bag (20 kg) of the levelling compound in around 4.4 litres of cold water
  • Mix into a consistent mass with a power mixer or a drill paddle.
  • Spread the plaster on the base while pressing hard and rake it.
  • Workable for about three hours after adding water
  • Wash tools with water immediately after completing the work
  • Remove dried plaster mechanically
  • Choose the tooth size of the plastering trowel according to the size of the tile and the adhesion surface.

Grouting

  • Grout after around one day with absorbent bases; with solid bases and waterproofed surfaces, grout after 2-5 days.

Other considerations

  • The information is based on tests and practical experience. We cannot affect conditions at the work site so we cannot assume responsibility for the end result affected by local conditions.

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Materiaalimenekki

2-5 kg/m² depending on the base and the tile
Vedentarve max. 4.4 l/20 kg
Sideaine special cement and polymer compound
Väri gray
Maksimiraekoko

0.6 mm
Pakkauskoko 20 kg
Varastointi

1 year in a dry location
Käyttölämpötila

+10°C...+25°C
Työstettävyysaika approx. 3 h
Avoin aika approx. 20 min
Saumattavissa 1-5 days
Vastuunrajaus, tuotteen käyttöön liittyvät huomiot ja rajoitukset: Tutustu Fescon Oy:n yleisiin toimitusehtoihin ja tuotteeseen liittyviin suunnittelu- sekä työohjeisiin.