Contact us
+358 20 789 5900 or with form
Offer request 0
Floor compound LM 6000
Underfloor heating filler LL 5500
Coarse floor levelling compound LM 5000
Floor levelling plaster LT 4000
Floor concrete LB 7
Fescorapid
Fescofine
FlowPlan
Flow CS
Flow FS
FlowBase
Flow GS 3.0 mm Gypsum floor mass
Flow Primer
Primer PLUS
Elevation mark
Bordering strip 30x30x2000 mm
Bordering strip 8x150 mm
Separation fabric 1.5x50 m
« Back to the product group

Fescofine

Ask for more information

Product description

Containing special cement binder, Fescofine is a fast-hardening and fast-drying versatile finishing plaster for floors, walls and ceiling. Suitable for both indoor and outdoor use. 

  • For layer thicknesses of 0 - 5 mm, maximum thickness of 10 mm in patch filling
  • Manually levelled
  • Easy to work with
  • Coatable approx. 2 h
  • Paste-like consistency

Applications

  • For the quick levelling of concrete surfaces
  • For repairing holes in concrete floors, correcting floor grading, and repairing and levelling stairs
  • Repairs to concrete surfaces, including wall and ceiling surfaces
  • Suitable for indoor and outdoor use
The product is listed in the portal for building products that can be used in Nordic Swan Ecolabelled buildings.
GTIN code Product name Product number Package size
6416841202390 FESCOFINE 20 KG 20239 20 kg

Base

  • Concrete substrates
  • The base is clean, solid and vacuum-cleaned
  • Loose layers, cement paste, and other impurities have been mechanically removed to ensure adhesion
  • Smooth concrete surfaces should be coarsened
  • Sufficient strength, load-bearing capacity and immobility
  • The tensile strength of the base must be > 1.0 MPa
  • The temperature of the underfloor structure is > +10°C and relative humidity < 95% RH The relative humidity of the underfloor structure affects the setting of the floor levelling compound

Priming

  • Priming is performed according to the instructions of Fescon Adhesive Primer or Flow Primer, depending on the base
  • Impermeable surfaces, such as ceramic tiles, epoxy and metal surfaces, are pre-treated according to the instructions for Fescon Primer PLUS
  • No primers are used in outdoor installations. To prime the surface, wet it with water roughly an hour before applying Fescofine. The surface should be matte there must be no puddles of water on the surface

Work instructions

  • Working time is around 15 minutes from adding the water
  • The work area must be completely protected from wind, draft, sun and rain.
  • During work, the indoor temperature must be +10…+25 °C and the relative humidity more than 40%.
  • A sack (20 kg) of plaster is mixed with 6.0–6.5 litres of cold water.
  • Do not use any excess water, because it weakens the finishing plaster’s strength properties, increases the risk of bleeding and extends the drying period.
  • Mix into a smooth paste with a mixing paddle connected to a power drill.
  • The finishing plaster is spread with a steel trowel on the surface to be levelled
  • Wash the tools with water immediately after finishing work
  • Remove dried levelling compound mechanically

Coating

  • The floor compound can be waterproofed directly with products from the certified Fescon waterproofing system 
  • Can be covered with ceramic tiles, plastic coatings, textile mats, vinyl tiles, wood parquet or laminate, as well as cork
  • However, it must be ensured that the levelling compound, concerning its technical properties, meets the requirements of the manufacturer of the floor covering and RYL for bases to be covered, with the entire structure in mind
  • To dry properly, the finishing plaster requires a relative indoor air humidity of below 50% and temperatures above 20 °C. Poor conditions compromise the strength of the finishing plaster and prolong the drying time

Storage and handling of waste
See the separate storage and disposal instructions https://www.fescon.fi/en/material-bank

Material usage

1 mm layer approx. 1.5 kg/m²
Water requirement 6.0-6.5 l / 20 kg
Type powder
Binder special cement
Colour bleached gray
Maximum grain size

0.1 mm
Package size 20 kg
Storage

storage time in a dry location approx. 10 months
Layer thickness

0 - 5 mm
Fibre non-fibre reinforced
Additives

substances improving workability, casein-free
Usage temperature

+10°C...+25°C
Workability time approx. 15 min
Coatable approx. 2 h (+20°C, RH 50 %)
Walkable approx. 2 h (+20°C, RH 50 %)
Compressive strength

> 15 MPa (28 days, +20°C, RH 50 %)
Adhesion strength

> 1,5 MPa for concrete (7 day +20°C, RH 50 %)
Flexural bond strength F 5 (EN 13813)
Surface tensile strength > 1,5 MPa (28 days , +20°C, RH 50 %) as with Fescorapid
Frost resistance frost resistant, suitable for indoor and outdoor use
pH < 11 low alkaline (hardened material)
Waterproofness

waterproof
Limitation of liability, product use notes and restrictions: Please familiarize yourself with Fescon Oy's general terms of delivery and the design and work instructions related to the product.