Contact us
+358 20 789 5900 or with form
Offer request 0
Floor compound LM 6000
Underfloor heating filler LL 5500
Coarse floor levelling compound LM 5000
Floor levelling plaster LT 4000
Floor concrete LB 7
Fescorapid
Fescofine
FlowPlan
Flow CS
Flow FS
FlowBase
Flow GS 3.0 mm Gypsum floor mass
Flow Primer
Primer PLUS
Elevation mark
Bordering strip 30x30x2000 mm
Bordering strip 8x150 mm
Separation fabric 1.5x50 m
« Back to the product group

Floor compound LM 6000

Ask for more information

Product description

The Fescon LM 6000 is a casein-free manually applied floor levelling compound with a special cement binder that hardens and dries rapidly. 

  • A surface that can be waterproofed in one work stage
  • For layer thicknesses 10-250 mm
  • Manually levelled
  • Dries through hydration

Applications

  • For casting, straightening and filling concrete floors and creating floor grading in flats, offices and public buildings
  • If necessary, the surface can be finished using the Fescon LT 4000 floor levelling compounds
  • Can be used on floating, reinforced floors, in which case the minimum thickness is 50 mm
The product is listed in the portal for building products that can be used in Nordic Swan Ecolabelled buildings.
GTIN code Product name Product number Package size
6416841202000 FLOOR COMPOUND LM 6000 20 KG 20200 20 kg

Base

  • Clean, solid and dust-free
  • Sufficient strength, load-bearing capacity and immobility
  • Relative humidity < 95% RH
  • Temperature > +10°C...+25°C
  • Loose layers, cement paste and other impurities must be mechanically removed

Priming

  • Carry out the priming in accordance with Fescon Adhesive Primer instructions, depending on the base
  • When beginning the levelling work, there must be no puddles of primer

Instructions for use

  • Mix a bag (20 kg) of dry compound in 1.7-2.0 litres of cold water
  • Mix the LM 6000 into a consistent paste using a drill paddle
  • Spread the compound onto the base, and level or float it with a steel trowel. Perform the spreading, levelling and floating in one go; if compacting is required, use vibration
  • Workable for about half an hour after adding water
  • Wash tools with water immediately after completing the work
  • Remove dried levelling compound mechanically
  • The floor must be built as a floating, reinforced structure if the base is weak concrete (adhesion < 0.5 MPa), wood, or insulation

Covering

  • Overlay the cast surfaces with Fescon manual levelling compound
  • we do not recommend leaving the floor compound without coating

Other considerations

  • You must nevertheless ensure that the plaster’s technical properties meet the requirements set by the floor coating manufacturer and RYL, taking into account the entire structure. The straightness of the finishing plaster is measured, if necessary, under RT guideline 14-11039.

Storage and handling of waste
See the separate storage and disposal instructions https://www.fescon.fi/en/material-bank

Material usage

approx. 1.8 kg/m²/1 mm
Water requirement 1.7-2.0 l / 20 kg
Finished compound 10-11 l/20 kg
Type powder
Binder special cement
Colour gray
Maximum grain size

1.2 mm
Package size 20 kg
Storage

storage time in a dry location approx. 12 months
Usage temperature

+10°C...+25°C
Workability time approx. 0.5 h
Coatable approx. 24 h (+20°C/RH 50%)
Walkable approx. 3 h
Hardening time

approx. 1 day at +20°C
Strength class C 30 (EN 13813)
Compressive strength

> 30 MPa (28 days, +20°C, RH 50 %)
Flexural bond strength F 5 (EN 13813)
Surface tensile strength > 1,0 MPa (28 vrk, +20°C, RH 50 %)
Waterproofness

waterproof
Limitation of liability, product use notes and restrictions: Please familiarize yourself with Fescon Oy's general terms of delivery and the design and work instructions related to the product.